Here down the page you will discover some very good insight when it comes to How to Install a Bathtub.
Installing a bath tub isn't precisely rocket science, but it does require solid plumbing, woodworking, as well as often, tiling abilities. Replacing an old bath tub with a brand-new one is also a moderately hard job. If the old tub is readily available, the task can move rapidly; if you need to open a wall surface to get rid of the old bathtub as well as place the brand-new tub, the job is a lot harder. In either situation, the job is within a home handyman's skills, although you will certainly need an assistant to leave the old bathtub as well as set in the brand-new one. Ensure you have actually qualified yourself for the task and also are comfortable trying it. Rather than employing a service provider to take control of a halfway-completed project, it is far better to consider employing one prior to you begin. Chances are you may require a professional plumber to make tube links.
This article will aid you set up a brand-new bath tub in your restroom if you have already gotten a brand-new tub and don't need to alter the setup of your previous water supply pipelines.
Your tools and product list must comprise the following:
Getting ready for the Installation
To start with, the supporting frame supplied with the bathroom needs to be fitted (if needed) according to the supplier's directions. Next, fit the taps or mixer to the tub. When fitting the faucet block, it is necessary to see to it that if the tap features a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets system to prevent pressure on the bathtub.
Fit the flexible faucet adapters to the bottom of the two faucets making use of 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. See to it you utilize every one of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should currently prepare to be fitted in its last position.
Removing Old Touches
If you require to replace old taps with new ones as a part of your installment, after that the first thing you ought to do is disconnect the supply of water. After doing so, turn on the faucets to drain any type of water remaining in the system. The procedure of removing the existing taps can be rather problematic as a result of the limited access that is often the situation.
Use a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the taps. Have a fabric prepared for the staying water that will originate from the pipes. As soon as the supply pipes have actually been removed, make use of the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary faucets from turning throughout this procedure. Once the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any type of old securing substance.
Prior to moving on to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Mounting the Bathtub
Using both wood boards under its feet, put the bathtub in the required placement. The wooden boards are valuable in evenly spreading out the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 small points.
The following objective is to ensure that the bath tub is leveled all round. This can be accomplished by inspecting the level and also readjusting the feet on the bath tub up until the spirit level reads degree.
To set up taps, fit the bottom of the outermost adaptable tap adapter to the proper supply pipeline by making a compression sign up with; after that do the exact same for the other faucet.
Activate the water and examine all joints as well as brand-new pipework for leaks as well as tighten them if essential. Fill up the bath tub as well as also check the overflow outlet and also the typical outlet for leaks.
Ultimately, deal with the bath paneling as described in the producer's instruction manual. Tiling and also sealing around the bath tub ought to wait till the tub has actually been utilized at least when as this will settle it right into its final setting.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will need a plastic connector to stop damages to the thread. One end of the port fits on the plastic tail of the faucet and the other end gives a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly need decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, place the tap in the installing hole in the bath/basin guaranteeing that the washing machines are in location between the tap and the sink. Secure the faucet in position with the producer provided backnut. As soon as the faucet is securely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal tap ports. The former type ought to be attached to the faucet finishes first, tightening just by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the installation can relocate sufficient to break a rigid seal, causing the water to pass through the wall between the bath as well as the tiling, bring about difficulties with moisture as well as feasible leaks to the ceiling below.
You can select from a selection of coloured sealants to assimilate your fixtures and also installations. They are offered in tubes as well as cartridges, and also are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with twists of soaked paper or soft rope. Bear in mind to constantly load the bath tub with water prior to sealing, to allow for the motion experienced when the tub remains in usage. The sealer can fracture rather very early if you do not think about this movement prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise conveniently offered on the marketplace. It is recommended to fit the floor tiles using water-resistant or water resistant sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our topic on Installing A Bathtub. Thanks so much for spending some time to read through our article. Those who liked our page kindly don't forget to share it. Thank you for your time. Visit us again soon.
24/7 emergency? We're here!